Produse pentru componentă epoxidică (14)

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Thermally conductive tapes offer high performance heat dissipation; vital requirements for designing electronic devices where demand is for slimmer and more powerful features. Thermally conductive tapes offer a clean alternative to pastes and liquid adhesives and can be die-cut to bespoke designs, providing efficiency of application and reducing assembly times. Double coated and transfer thermally conductive tapes are available in a variety of thicknesses

Wir bieten Ihnen eine große Auswahl an Technischen Kunststoffen und ermitteln für Sie den technisch und wirtschaftlich optimalen Kunststoff für Ihre Anforderungen.

ISONEM SHINE FLOOR est une résine de sol autolissante à base de polyuréthane et de solvant (bi composants).

Colles polymérisant à température normale ou par chauffage Température normal 50°C

1-komponentiger Kleb-und Dichtstoff auf Basis von MS-Polymer Verbrauch ca. bei 5 mm x 5 mm Fugen 12-14 Laufmeter pro Kartusche (290 ml).

DESCRIPTION Façacryl est une peinture de dispersion acrylique de haute qualité spécialement conçue pour les façades. Très bonne adhérence sur toutes les surfaces minérales et diverses. Bon pouvoir couvrant, ne jaunit pas, respirant, parfaitement lavable et bon tendu. Rendement (indicatif) : 6-9 m²/L, selon le support Valeurs limites de l’UE pour ce produit (COV) : Cat. A/a : 30 g/L (2010). Ce produit contient moins de 30 g/L de produits COV.

Sosyal yaşantımızın mekansal sınırlayıcısı mimari yapıların tasarımında kullanılan, estetik, şık görünümlü, pürüzsüz, çağdaş bir yapı malzemesidir. Oldukça geniş bir kullanım alanı olan Naturalbond, renk çeşidi ve bütünlüğü, hava etkilerine dayanımı, kolay şekil verilebilirliği, ısı ve ses tutucu özelliği sayesinde diğer yapı malzemelerine göre daha üstündür. Aynı zamanda çevre dostu olan Naturalbond, mukavim yapısı sayesinde diğer yapı malzemelerine oranla daha geniş açıklıklarda rahatça kullanılabilmektedir. Düşük maliyetle yüksek verim avantajı, Naturalbond’u vazgeçilmez kılmaktadır.

Xypex Concentrate is the most chemically active product within the Xypex Crystalline Waterproofing System.When mixed with water, this light grey powder is applied as a cementitious slurry coat to above-grade or below-grade concrete, either as a single coat or as the first of a two-coat application. It is also mixed in Dry-Pac form for sealing strips at construction joints, or for the repairing of cracks, faulty construction joints and honeycombs. Xypex prevents the penetration of water and other liquids from any direction by causing a catalytic reaction that produces a non-soluble crystalline formation within the pores and capillary tracts of concrete and cement-based materials.

Application: ElectrophoresisGenetic testing : Amides Storing temperature: 2-8°C GHS pictogram: GHS07GHS08 Shipping condition: ambient Synonym: Propensäureamid 2-Propenamid Acrylsäureamid IUPAC: Prop-2-enamide Appearance: clear colorless solution UNSPSC-No: 41105319 Code:1138 Manufacturers:GERBU

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Accessoires Colle universelle de contact à pistoler à base de polychloroprène (Néoprène®) en canister spécial pour un pistolage immédiat sans la moindre installation de pistolage. Prête à l'emploi immédiatement et particulièrement écologique, utilisable avec un pistolet, ne nécessite pas d'air comprimé ou d'électricité, séchage et force d'adhérence initiale très rapides, rapide à mettre en oeuvre, pas d'entretien, toujours prêt à pistoler, très faible consommation, résistante à l'humidité, très haute résistance aux températures (jusqu'à +115°C), résistante aux acides et bases légers, sans toluène et chlorure de méthylène Accessoires 47100275 DISSOL SPRAY POUR COLLE CONTACT 500ML 47100612 CLEANING ADAPTOR NEOSPRAY - DISSOL SPRAY 47100615 FLEXIBLE NEOSPRAY 4M 47100620 PISTOLET NEOSPRAY 47100625 BUSE DE RECHANGE PISTOLET NEOSPRAY

Application: ElectrophoresisGenetic testing : Amides Storing temperature: 2-8°C GHS pictogram: GHS06GHS08 Shipping condition: ambient Synonym: Propensäureamid 2-Propenamid Acrylsäureamid IUPAC: Prop-2-enamide Appearance: clear colorless solution UNSPSC-No: 41105319 Code:1807 Manufacturers:GERBU

Application: ElectrophoresisGenetic testing : Amides Storing temperature: 2-8°C GHS pictogram: GHS07GHS08 Shipping condition: ambient Synonym: Propensäureamid 2-Propenamid Acrylsäureamid IUPAC: Prop-2-enamide Appearance: clear colorless solution Code:1107 Manufacturers:GERBU